Pure Series Dry Bath

Product model:

Thermal Control Series

MESSAGE

product details

It is an economical dry bath incubator controlled by a microprocessor, using high-purity aluminum as the thermal conductive medium to replace traditional water baths. It features elegant appearance, easy operation, high accuracy, and compact size. It can be widely used for sample preservation and reactions, DNA amplification and pre-denaturation for electrophoresis, serum coagulation, etc.

Automatic fault detection and buzzer alarm function, temperature deviation calibration function, real-time temperature and countdown display, elegant appearance, blue LCD display of real-time parameter information.

Multiple safety protections ensure long-term operational stability and safety under unattended conditions, complying with CE standards.

Supports module-specific custom calibration function, built-in over-temperature protection device.

Real-time temperature and countdown display.

Parameter	Value
Model	L-100
Temperature Setting Range	-10℃~100℃
Temperature Control Range	Ambient temperature minus 30℃~100℃
Time Setting	1min ~ 99h59min/∞
Temperature Control Accuracy	≤±0.3℃*
Display Accuracy	0.1℃
Temperature Uniformity	≤±0.3℃*
Heating Time	≤12 minutes (25℃ to 100℃)*
Cooling Time 1	≤10 minutes (100℃ to 25℃)*
Cooling Time 2	≤25 minutes (room temperature to ambient minus 30℃)*
Multi-point Operation	Supported (max 5 points)
Multi-point Cycle Operation	Supported (max 99 cycles)
Automatic Preheating	Supported
Auto-start on Power-on	Supported
Automatic Recovery after Power Failure	Supported
Sample Capacity	See module selection table
Input Power	150W
Voltage	AC220V/50-60Hz
Fuse	250V 3A Φ5×20
Dimensions	260×195×150 mm
Weight	4.5Kg

Product parameters
Microcomputer controlled cooling metal bath

Model number	L-100
Temperature setting range	-10°C~100°C
Temperature control range	Below room temperature 30°C~100°C
Time setting	1min ~ 99h59min/∞
Temperature control accuracy	≤±0.3°C*
Accuracy of display	0.1°C
Uniformity of temperature	≤±0.3°C*
Heating up time	≤12minutes (25°C至100°C) *
Cooling time1	≤10minutes (100°C至25°C) *
Cooling time2	≤25minutes (Room temperature to below room temperature30°C) *
Multi-point operation	Support (Maximum 5 points)
Multi-point loop operation	Support (The maximum number of cycles is 99 times)
Automatic preheating	Support
Start automatic operation	Support
Automatic recovery of power failure	Support
Volume of sample	See the module selection table
Input power	150W
voltage	AC220V/50-60HZ
Fuse breaker	250V 3A Φ5×20
Size	260x195x150 mm
weight	4.5Kg

Module model	Number of tubes and pore size
L30	96×0.2ml (standard edition)
L31	54×0.5ml (centrifuge tube)
L32	35×1.5ml (Centrifuge tube)
L33	35×2.0ml (centrifuge tube)
L34	15×0.5ml+20×1.5ml (centrifuge tube)
L35	96×0.2ml (microplate)
L36	24×5ml (centrifuge tube)
L37	15×10ml (centrifuge tube)
L38	12×15ml (centrifuge tube)
L39	6×50ml (50ml round bottom centrifuge tube)
L39-S	6×50ml (50ml conical bottom centrifuge tube)

Product parameters
Microcomputer controlled cooling metal bath

	CH-100 (Heating up)	CL-100 (refrigeration)
Type of equipment	-	-
Module Specification	CHSeries module	CLSeries module
Temperature setting range	0°C~100°C	-10°C~100°C
Temperature control range	Room temperature+5°C~100°C	Below room temperature 25°C~100°C
Time setting	1sec~99h59min/∞	1sec~99h59min/∞
Temperature control accuracy (37°C when)	≤±0.3°C	≤±0.3°C
Accuracy of display	0.1°C	0.1°C
Uniformity of temperature (37°C when)	≤±0.3°C	≤±0.3°C
Heating up time	≤12minutes(25°C~100°C)	≤12 minutes (25°C~100°C)
Heating up time1	/	≤12 minutes (100°C~25°C)
Heating up time2	/	≤25 min (room temperature drops to 25°C below room temperature)
Hot cover temperature setting range	OFF~+10°C	OFF~+10°C
Heat cover temperature control accuracy	≤±0.5°C	≤±0.5°C
Heat cover heating time	≤10minutes(25°C~100°C)	≤10 minutes (25°C~100°C)
The samples were stored at 4°C at the end of operation	Support	Support
Multi-point operation	Support (Maximum 5 points)	Support (Maximum 5 points)
Multi-point loop operation	Support (The maximum number of cycles is 99)	Support (The maximum number of cycles is 99)
Automatic preheating	Support	Support
Start automatic operation	Support	Support
Automatic recovery of power failure	Support	Support
Volume of sample	See module selection table	See module selection table
Input power	150W	150W
voltage	AC220V/50-60HZ	AC220V/50-60HZ
Fuse breaker	250V 3A Φ5×20	250V 3A Φ5×20
Dimensions of appearance	300×200×210mm	300×200×210mm
weight	4.0 Kg	4.0 Kg

Model of module	Sample size	Temperature control range
CL-01	35 x 2.0mL Centrifuge tube	RT-25°C~100°C
CL-02	35 x 1.5mL Centrifuge tube	RT-25°C~100°C
CL-03	54 x 0.5mLCentrifuge tube	RT-25°C~100°C
CL-04	96 x 0.2mL PCRStandard plate	RT-25°C~100°C
CL-05	96 x 0.2mL Enzyme labeled plate	RT-25°C~100°C
CH-06	35 x 2.0mL Centrifuge tube	RT+5°C~100°C
CH-07	35 x 1.5mL Centrifuge tube	RT+5°C~100°C
CH-08	54 x 0.5mLCentrifuge tube	RT+5°C~100°C
CH-09	96 x 0.2mL PCRStandard plate	RT+5°C~100°C
CH-10	96 x 0.2mL Enzyme labeled plate	RT+5°C~100°C

Product Message

For suggestions or feedback, please submit your information, and we will contact you promptly, or call us directly.